manualshive.com logo in svg

Yamaha WOLVERINE 350 YFM35XY, Owner'S Manual, Page: 81 / 128

Share
Download
Yamaha WOLVERINE 350 YFM35XY Owner'S Manual Download Page 81

8-10

8

To install the spark plug

1. Measure the spark plug gap with a wire thick-

ness gauge and, if necessary, adjust the gap
to specification.

2. Clean the surface of the spark plug gasket

and its mating surface, and then wipe off any
grime from the spark plug threads.

3. Install the spark plug with the spark plug

wrench, and then tighten it to the specified
torque.

TIP

If a torque wrench is not available when installing
a spark plug, a good estimate of the correct torque
is 1/4–1/2 turn past finger tight. However, the spark
plug should be tightened to the specified torque as
soon as possible.

4. Install the spark plug cap.

EBU23315

Engine oil and oil filter cartridge 

The engine oil level should be checked before
each ride. In addition, the oil must be changed and
the oil filter cartridge replaced at the intervals spec-
ified in the periodic maintenance and lubrication
chart.

To check the engine oil level

1. Place the ATV on a level surface.

Specified spark plug:

NGK/DR8EA

Spark plug gap:

0.6–0.7 mm (0.024–0.028 in)

1. Spark plug gap

Tightening torque:

Spark plug:

17.5 Nm (1.75 m·kgf, 12.7 ft·lbf)

U3D563E0.book  Page 10  Monday, May 12, 2008  11:12 AM

Summary of Contents for WOLVERINE 350 YFM35XY

































































































































Reviews:

No comments