manualshive.com logo in svg

Yamaha WOLVERINE 350 YFM35XY, Owner'S Manual, Page: 104 / 128

Share
Download
Yamaha WOLVERINE 350 YFM35XY Owner'S Manual Download Page 104

8-33

8

WARNING

EWB02130

Inspect cables frequently and replace if dam-
aged. Corrosion can result when the cable
sheaths become damaged, and cables can
also become frayed or kinked, which could re-
strict the operation of controls and lead to an
accident or injury.

EBU28711

Checking and lubricating the front and 
rear brake levers 

The operation of the front and rear brake levers
should be checked before each ride, and the lever
pivots should be lubricated if necessary.

EBU28832

Checking and lubricating the brake 
pedal 

The operation of the brake pedal should be
checked before each ride, and the pedal pivot
should be lubricated if necessary.

TIP

To access the brake pedal pivot, remove panel A.
(See page 8-8.)

Recommended lubricant:

Engine oil

Recommended lubricants:

Front brake lever:

Silicone grease

Rear brake lever:

Lithium-soap-based grease

Recommended lubricant:

Lithium-soap-based grease

U3D563E0.book  Page 33  Monday, May 12, 2008  11:12 AM

Summary of Contents for WOLVERINE 350 YFM35XY

































































































































Reviews:

No comments