Yamaha WOLVERINE 350 YFM35XY Owner'S Manual Download Page 6 | Manualshive

Page: 6 / 128

Yamaha WOLVERINE 350 YFM35XY Owner'S Manual Download Page 6

EBU17330

IMPORTANT MANUAL INFORMATION

EBU17342

FAILURE TO FOLLOW THE WARNINGS CONTAINED IN THIS MANUAL CAN RESULT IN SERIOUS IN-
JURY OR DEATH.
Particularly important information is distinguished in this manual by the following notations:

* Product and specifications are subject to change without notice.

This is the safety alert symbol. It is used to alert you to potential per-
sonal injury hazards. Obey all safety messages that follow this sym-
bol to avoid possible injury or death.

A WARNING indicates a hazardous situation which, if not avoided,
could result in death or serious injury.

A NOTICE indicates special precautions that must be taken to avoid
damage to the vehicle or other property.

A TIP provides key information to make procedures easier or clearer.

WARNING

NOTICE

TIP

U3D563E0.book Page 1 Monday, May 12, 2008 11:12 AM

«
...
4
5
6
7
8
...
»

Summary of Contents for WOLVERINE 350 YFM35XY

































































































































Reviews:

No comments