manualshive.com logo in svg

Yamaha WaveRunner GP800R 2001, Owner'S/Operator'S Manual, Page: 96 / 123

Share
Download
Yamaha WaveRunner GP800R 2001 Owner'S/Operator'S Manual Download Page 96

4-16

E

NOTE:

●

Wipe off any water on the spark plug or
inside the cap before installing the spark
plug cap. Push the spark plug cap down
until it clicks.

●

If a torque wrench is not available when
you are fitting a new spark plug, a good
estimate of the correct torque is 1/4 turn
to 1/2 turn past finger tight. Have the
spark plug adjusted to the correct torque
with a torque wrench as soon as possible.

WARNING

Be careful not to damage the insulator
when removing or installing a spark plug.
A damaged insulator could allow sparks
to escape, which could lead to explosion
or fire.

EJU00553a

Lubrication points

To keep moving parts sliding or rotating

smoothly, coat them with water-resistant
grease.

Recommended water-resistant grease:

Yamaha Marine Grease/
Yamaha Grease A

●

Throttle cable (carburetor end)

●

Oil pump cable

●

Choke cable (carburetor end)

Summary of Contents for WaveRunner GP800R 2001




























































































































Reviews:

No comments