Yamaha WaveRunner GP800R 2001 Owner'S/Operator'S Manual Download

Page: 30 / 123

2-6

EJU00703

Hood

To open the hood, push the latch

down, and then lift the hood up.

To close the hood, push the hood down to

lock it in place.

NOTE:

Make sure that the hood is properly secured
before operating the watercraft.

EJU00347

Fuel tank filler cap

To remove the fuel tank filler cap

, turn it

counterclockwise.

NOTE:

Make sure that the fuel tank filler cap is
properly secured before operating the water-
craft.

EJU00001N

Oil tank filler cap

To remove the oil tank filler cap

, turn it

counterclockwise.

NOTE:

Make sure that the oil tank filler cap is prop-
erly secured before operating the watercraft.

Summary of Contents for WaveRunner GP800R 2001




























































































































Search results

Summary of Contents for WaveRunner GP800R 2001

Reviews:

Related manuals for WaveRunner GP800R 2001

Brands by name

Popular brands

Yamaha WaveRunner GP800R 2001, Owner'S/Operator'S Manual

Search results

Summary of Contents for WaveRunner GP800R 2001

Reviews:

Related manuals for WaveRunner GP800R 2001

Brands by name

Popular brands