Yamaha WaveRunner GP800R 2001 Owner'S/Operator'S Manual Download

Page: 92 / 123

4-12

EJU00544

Inspecting the oil injection
system

Check the oil injection system for leakage,

cracks, or malfunctions. If necessary, have a
Yamaha dealer repair the oil injection sys-
tem.

Check:

●

Oil tank for damage, cracks or leakage.

●

Oil tank for water or dirt.

●

Oil hose and joint for damage or cracks.

●

Oil filter for dirt.

●

Oil pump for leakage.

Oil tank

Check the oil tank for leakage or water in

the tank. If water is found in the oil injection
system or if the oil tank needs to be cleaned
have a Yamaha dealer service the water-
craft.

Oil filter

Check the oil filter for dirt and clogs. If the

oil filter is clogged, remove it from the oil
tank together with the oil level sender and
clean it.

Summary of Contents for WaveRunner GP800R 2001




























































































































Search results

Summary of Contents for WaveRunner GP800R 2001

Reviews:

Related manuals for WaveRunner GP800R 2001

Brands by name

Popular brands

Yamaha WaveRunner GP800R 2001, Owner'S/Operator'S Manual

Search results

Summary of Contents for WaveRunner GP800R 2001

Reviews:

Related manuals for WaveRunner GP800R 2001

Brands by name

Popular brands