Yamaha WaveRunner GP800R 2001 Owner'S/Operator'S Manual Download

Page: 90 / 123

4-10

EJU00537

Inspecting the fuel system

WARNING

Gasoline and its vapors are highly flam-
mable and explosive.

Check the fuel system for leaks, cracks,

or malfunctions. If any problem is found, do
the necessary repair or replacement as
required. If repair is necessary, consult a
Yamaha dealer.

Check:

●

Carburetor for leakage.

●

Fuel pump for malfunction or leakage.

●

Fuel tank for water or dirt.

●

Fuel tank for damage, cracks or leakage.

●

Fuel hose joint for leakage.

●

Fuel hose for cracks or other damage.

●

Fuel filter for leakage.

●

Fuel cock for leakage.

●

Air vent check valve for leakage.

●

Fuel tank filler cap for damage.

WARNING

Failure to check for and repair any fuel
leakage may result in fire or explosion.

Summary of Contents for WaveRunner GP800R 2001




























































































































Search results

Summary of Contents for WaveRunner GP800R 2001

Reviews:

Related manuals for WaveRunner GP800R 2001

Brands by name

Popular brands

Yamaha WaveRunner GP800R 2001, Owner'S/Operator'S Manual

Search results

Summary of Contents for WaveRunner GP800R 2001

Reviews:

Related manuals for WaveRunner GP800R 2001

Brands by name

Popular brands