manualshive.com logo in svg

Yamaha WaveRunner GP800R 2001, Owner'S/Operator'S Manual, Page: 84 / 123

Share
Download
Yamaha WaveRunner GP800R 2001 Owner'S/Operator'S Manual Download Page 84

4-4

E

4. Install the cap securely.
5. Remove the spark plugs and pour

approximately one tablespoon of engine
oil into each cylinder. Grease the spark
plug threads and install the spark plugs.

6. Lubricate all cables such as the throttle,

choke, and steering cables.

NOTE:

Use a Yamaha Power Cable Luber and
Yamaha Lube-Zall to pressure lubricate the
cables and purge out any moisture between
the inner and outer cables.

7. Lubricate the areas of the watercraft

specified under Lubrication points on
page 4-16.

EJU00528a

Fuel system

Top off the fuel tank with fresh gasoline

and add one ounce of Yamaha Fuel Stabi-
lizer and Conditioner to each gallon of fuel.

NOTE:

Use of Yamaha Fuel Stabilizer and Condi-
tioner eliminates the need to drain the fuel
system. If the fuel system is to be drained
instead, consult a Yamaha dealer.

Summary of Contents for WaveRunner GP800R 2001




























































































































Reviews:

No comments