Yamaha WaveRunner GP800R 2001 Owner'S/Operator'S Manual Download

Page: 102 / 123

4-22

EJU00578a

Replacing the fuse

The fuse is in the electrical box

To replace the fuse:

1. Remove the cap

, pull out the red lead,

and bring the fuse holder

out of the

electrical box.

2. Open the fuse holder and replace the

fuse

with one of the correct amper-

age.

WARNING

Do not use fuses of higher amperage that
those recommended. Substitution of a
fuse of improper rating can cause exten-
sive electrical system damage and possi-
ble fire.

EJU00580

Bleeding the oil injection
pump

If the oil tank becomes completely empty,

or any hose connected to the oil pump has
been disconnected, the oil pump must be
bled to ensure proper oil flow.

If bleeding of the oil pump is necessary,

have a Yamaha dealer bleed it.

Fuse amperage: 10 A

Summary of Contents for WaveRunner GP800R 2001




























































































































Search results

Summary of Contents for WaveRunner GP800R 2001

Reviews:

Related manuals for WaveRunner GP800R 2001

Brands by name

Popular brands

Yamaha WaveRunner GP800R 2001, Owner'S/Operator'S Manual

Search results

Summary of Contents for WaveRunner GP800R 2001

Reviews:

Related manuals for WaveRunner GP800R 2001

Brands by name

Popular brands