Yamaha VZ200D Owner'S Manual Download

Page: 43 / 80

Operation

sure.

Models equipped with trim rods: Once
the outboard motor is supported with the
tilt support lever, press the power trim
and tilt switch “

” (down) to retract the

trim rods.

CAUTION:

ECM00250

Be sure to retract the trim rods complete-
ly during mooring. This protects the rods
from marine growth and corrosion which
could damage the power trim and tilt

mechanism.

EMU28052

Procedure for tilting down

Power trim and tilt models / power tilt models
1.

Push the power tilt / power trim and tilt
switch “

” (up) until the outboard motor

is supported by the tilt rod and the tilt
support lever / tilt support knob becomes
free.

Release the tilt support lever or pull out
the tilt support knob.

Push the power tilt / power trim and tilt
switch “

” (down) to lower the outboard

motor to the desired position.

EMU28060

Cruising in shallow water

The outboard motor can be tilted up partially
to allow operation in shallow water.

EMU28090

Power trim and tilt models / power tilt
models

The outboard motor can be tilted up partially

ZMU01884

ZMU01885

ZMU01936

ZMU01979

✩✰✬✬✤✤✤✲✣ ✦✫

Summary of Contents for VZ200D

















































































Search results

Summary of Contents for VZ200D

Reviews:

Related manuals for VZ200D

Brands by name

Popular brands

Yamaha VZ200D, Owner'S Manual

Search results

Summary of Contents for VZ200D

Reviews:

Related manuals for VZ200D

Brands by name

Popular brands