Yamaha VZ200D Owner'S Manual Download

Page: 68 / 80

Trouble Recovery

Q. Is heat range of spark plug incorrect?
A. Inspect spark plug and replace it with rec-
ommended type.

Q. Is high pressure fuel pump drive belt bro-
ken?
A. Have serviced by a Yamaha dealer.

Q. Is engine not responding properly to shift
lever position?
A. Have serviced by a Yamaha dealer.

Engine vibrates excessively.

Q. Is propeller damaged?
A. Have propeller repaired or replaced.

Q. Is propeller shaft damaged?
A. Have serviced by a Yamaha dealer.

Q. Are weeds or other foreign matter tangled
on propeller?
A. Remove and clean propeller.

Q. Is motor mounting bolt loose?
A. Tighten bolt.

Q. Is steering pivot loose or damaged?
A. Tighten or have serviced by a Yamaha
dealer.

EMU29431

Temporary action in

emergency

EMU29440

Impact damage

WARNING

EWM00870

The outboard motor can be seriously
damaged by a collision while operating or
trailering. Damage could make the out-

board motor unsafe to operate.

If the outboard motor hits an object in the wa-
ter, follow the procedure below.

Stop the engine immediately.

Inspect the control system and all com-
ponents for damage. Also inspect the
boat for damage.

Whether damage is found or not, return
to the nearest harbor slowly and careful-
ly.

Have a Yamaha dealer inspect the out-
board motor before operating it again.

EMU29471

Replacing fuse

If a fuse has blown, remove the electrical
cover, open the fuse holder and remove the
fuse with a fuse puller (if equipped). Replace
it with a spare one of the proper amperage.

WARNING

EWM00630

Be sure to use the specified fuse. An in-
correct fuse or a piece of wire could allow
excessive current flow. This could cause

electric system damage and a fire hazard.

NOTE:

Consult your Yamaha dealer if the new fuse

immediately blows again.

✩✰✬✬✤✤✤✲✣ ✩✦

Summary of Contents for VZ200D

















































































Search results

Summary of Contents for VZ200D

Reviews:

Related manuals for VZ200D

Brands by name

Popular brands

Yamaha VZ200D, Owner'S Manual

Search results

Summary of Contents for VZ200D

Reviews:

Related manuals for VZ200D

Brands by name

Popular brands