Yamaha VZ200D Owner'S Manual Download Page 45

Page: 45 / 80

Maintenance

EMU28216

Specifications

Dimension:

Overall length:

906 mm (35.7 in)

Overall width:

568 mm (22.4 in)

Overall height L:

1714 mm (67.5 in)

Transom height L:

493 mm (19.4 in)

Weight (without propeller) L:

245.0 kg (540 lb)

Performance:

Full throttle operating range:

4500–5500 r/min

Maximum output:

VZ200TR 147.1 kW@5000 r/min
(200 HP@5000 r/min)
VZ225TR 165.5 kW@5000 r/min
(225 HP@5000 r/min)
VZ250TR 183.9 kW@5000 r/min
(250 HP@5000 r/min)
VZ300TR 220.7 kW@5000 r/min
(300 HP@5000 r/min)

Idling speed (in neutral):

VZ200TR 700

30 r/min

VZ225TR 700

30 r/min

VZ250TR 700

30 r/min

VZ300TR 730

30 r/min

Engine:

Type:

2-stroke V

Displacement:

3342.0 cm

(203.93 cu.in)

Bore

stroke:

93.0

82.0 mm (3.66

3.23 in)

Ignition system:

TCI

Spark plug (NGK):

BKR6EKU

Spark plug gap:

1.5–1.6 mm (0.059–0.063 in)

Control system:

Remote control

Starting system:

Electric

Starting carburetion system:

Electronic fuel injection

Min. cold cranking amps (CCA/SAE):

512.0 A

Min. marine cranking amps (MCA/ABYC):

675.0 A

Min. reserve capacity (RC/SAE):

182 minutes

Alternator output for battery DC:

50.0 A

Drive unit:

Gear positions:

Forward-neutral-reverse

Gear ratio:

1.75 (28/16)

Trim and tilt system:

Power trim and tilt

Propeller mark:

Fuel and oil:

Recommended fuel:

Regular unleaded gasoline

Min. pump octane:

Recommended engine oil:

YAMALUBE 2-stroke outboard motor
oil

Lubrication:

Oil injection

Engine oil tank capacity:

1.2 L (1.27 US qt) (1.06 Imp.qt)

Remote oil tank capacity:

10.5 L (11.10 US qt) (9.24 Imp.qt)

Recommended gear oil:

Hypoid gear oil SAE#90

✩✰✬✬✤✤✤✲✣ ✧✣

Summary of Contents for VZ200D

















































































Search results

Summary of Contents for VZ200D

Reviews:

Brands by name

Popular brands

Yamaha VZ200D, Owner'S Manual

Search results

Summary of Contents for VZ200D

Reviews:

Brands by name

Popular brands