Yamaha Viking YXM70VPHH 2016 Owner'S Manual Download

Page: 67 / 172

5-8

EBU31851

Control cables

When driving in cold weather, always make
sure all control cables work smoothly before
starting off.

WARNING! Control cables can

freeze in cold weather and you could be
unable to control the vehicle.

[EWB03280]

EBU33050

Tires

Check tire pressure regularly to make sure it
is at the recommended specifications. Also
check for wear and damage.

Tire pressure

Use the tire pressure gauge to check and ad-
just tire pressures when the tires are cold. Tire
pressures must be equal on both sides.

WARNING! Operation of this vehicle with
improper tire pressure may cause severe
injury or death from loss of control or roll-
over. Tire pressure below the minimum

specified could also cause the tire to dis-
lodge from the rim under severe riding
conditions.

[EWB02542]

Set tire pressures to the following specifica-
tions:

UB427BE0.book Page 8 Friday, February 5, 2016 2:14 PM

Summary of Contents for Viking YXM70VPHH 2016













































































































































































Search results

Summary of Contents for Viking YXM70VPHH 2016

Reviews:

Related manuals for Viking YXM70VPHH 2016

Brands by name

Popular brands

Yamaha Viking YXM70VPHH 2016, Owner'S Manual

Search results

Summary of Contents for Viking YXM70VPHH 2016

Reviews:

Related manuals for Viking YXM70VPHH 2016

Brands by name

Popular brands