Yamaha Viking YXM70VPHH 2016 Owner'S Manual Download

Page: 159 / 172

9-3

4. Put the frame on stands or blocks to raise

all wheels off the ground.

5. Tie a plastic bag over the exhaust pipe

outlet to prevent moisture from entering.

6. If storing in a humid or salt-air atmo-

sphere, coat all exposed metal surfaces
with a light film of oil. Do not apply oil to
any rubber parts or the seat covers.

7. Remove the battery and charge it. Store

it in a dry place and recharge it once a
month. Do not store the battery in an ex-
cessively warm or cold place [less than 0
°C (30 °F) or more than 30 °C (90 °F)].

Use of fuel stabilizer eliminates the need to
drain the fuel system. Consult a Yamaha
dealer if the fuel system needs to be drained.

UB427BE0.book Page 3 Friday, February 5, 2016 2:14 PM

Summary of Contents for Viking YXM70VPHH 2016













































































































































































Search results

Summary of Contents for Viking YXM70VPHH 2016

Reviews:

Related manuals for Viking YXM70VPHH 2016

Brands by name

Popular brands

Yamaha Viking YXM70VPHH 2016, Owner'S Manual

Search results

Summary of Contents for Viking YXM70VPHH 2016

Reviews:

Related manuals for Viking YXM70VPHH 2016

Brands by name

Popular brands