Yamaha Viking YXM70VPHH 2016 Owner'S Manual Download

Page: 113 / 172

8-14

TIP

Skip steps 7–9 if the oil filter cartridge is not
being replaced.

7. Remove the oil filter cartridge with an oil

filter wrench. Make sure that the O-ring is
removed together with the oil filter car-
tridge. If the O-ring remains attached to
the crankcase, oil leakage may occur.

TIP

An oil filter wrench is available from a Yamaha
dealer.

8. Apply a light coat of clean engine oil to

the O-ring of the new oil filter cartridge.

TIP

Make sure that the O-ring is properly seated.

1. Engine oil drain bolt
2. Gasket

1. Oil filter cartridge
2. Oil filter wrench

UB427BE0.book Page 14 Friday, February 5, 2016 2:14 PM

Summary of Contents for Viking YXM70VPHH 2016













































































































































































Search results

Summary of Contents for Viking YXM70VPHH 2016

Reviews:

Related manuals for Viking YXM70VPHH 2016

Brands by name

Popular brands

Yamaha Viking YXM70VPHH 2016, Owner'S Manual

Search results

Summary of Contents for Viking YXM70VPHH 2016

Reviews:

Related manuals for Viking YXM70VPHH 2016

Brands by name

Popular brands