Yamaha Viking YXM70VPHH 2016 Owner'S Manual Download | Manualshive

Page: 121 / 172

background image

8-22

8

Changing the coolant

The coolant must be changed by a Yamaha
dealer at the intervals specified in the periodic
maintenance and lubrication chart.
Adding water instead of coolant lowers the
antifreeze content of the coolant. If water is
used instead of coolant, have a Yamaha deal-
er check the antifreeze content of the coolant
as soon as possible.
The radiator fan is automatically switched on
or off according to the coolant temperature in
the radiator.

NOTICE

ECB02260

Mix antifreeze with distilled water only.
However, if distilled water is not available,
soft water may be used for refilling.

If your vehicle overheats, see page 8-57 for
instructions.

EBU32400

Axle boots

Check the axle boots for holes or tears.
If any damage is found, have them replaced
by a Yamaha dealer.

Coolant reservoir capacity (up to the maxi-
mum level mark):

0.28 L (0.30 US qt, 0.25 Imp.qt)

1. Front axle boot

1

1

UB427BE0.book Page 22 Friday, February 5, 2016 2:14 PM

«
...
119
120
121
122
123
...
»

Summary of Contents for Viking YXM70VPHH 2016













































































































































































Reviews:

No comments

Related manuals for Viking YXM70VPHH 2016

Brand: MANCO Pages: 8

Brand: Taylor-Dunn Pages: 254

Transporta CCT 5221

Brand: Ifor Williams Trailers Pages: 45

Brand: Yamaha Pages: 134

Brand: Yamaha Pages: 206

Brand: Lil Pick Up Pages: 29

Brand: Ski-Doo Pages: 52

Brand: Logan Pages: 28

Brand: HTI Pages: 6

Brand: Landoll Pages: 88

Brand: Zhejiang Xinyang Pages: 37

Brand: Panasonic Pages: 392

Brand: HAUL MASTER Pages: 22

Brand: HAUL MASTER Pages: 28

Brand: KAYO MOTO Pages: 186

Brand: Knapen Trailers Pages: 20

Brand: Ace Sports Pages: 78

WOLVERINE YXE70WPXH

Brand: Yamaha Pages: 186

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands