background image

3 - 1

7

INSP

ADJ

3. Install:

Diaphragm

Brake master cylinder cap

NOTE:

If bleeding is difficult, it may be necessary to
let the brake fluid system stabilize for a few
hours. Repeat the bleeding procedure when
the tiny bubbles in the system have disap-
peared.

j. Add brake fluid to the level line on the

reservoir.

WARNING

Check the operation of the brake after
bleeding the brake system.

FRONT BRAKE ADJUSTMENT
TT-R125/TT-R125E

1. Check:

Brake lever free play 

a

 

Out of specification 

 Adjust.

2. Adjust:

Brake lever free play

NOTE:

For minute adjustment, loosen the locknut 

2

on the lever side and adjust with the adjuster

3

.

CAUTION:

Make sure that there is no brake drag after
adjusting the brake lever free play.

Brake lever free play 

a

:

10 ~ 15 mm (0.39 ~ 0.59 in) 

Brake lever free play adjustment steps:

Loosen the locknuts 

1

.

Turn the locknuts until free play 

a

 is

within the specified limits by changing their
tightening position.

Tighten the locknuts.

FRONT BRAKE ADJUSTMENT

Summary of Contents for TT-R125E(W)


































































































































































































































































































Reviews: