background image

46

A. No. The warranty on a new

Yamaha cannot be “voided” or

“canceled.” However, if a partic-

ular failure is caused by opera-

tion or maintenance other than as

shown in the Owner’s Manual,

that failure may not be covered

under warranty.

Q. Under what conditions is the

clutch not covered by warranty?

A. Clutches as well as clutch compo-

nents wear with use. Normal wear

is not covered under warranty

such service is the customer’s

responsibility. Abnormal wear is,

however, covered for one (1) year

from the date of purchase. Your

Yamaha snowmobile dealer pos-

sesses criteria as to what consti-

tutes abnormal wear.

Q. What responsibility does my

dealer have under this warranty?

A. Each Yamaha snowmobile dealer

is expected to:

1. Completely set up every new

machine before sale.

2. Explain the operation, mainte-

nance, and warranty require-

ments to your satisfaction at the

time of sale, and upon your

request at any later date.

3. In addition, each Yamaha snow-

mobile dealer is held responsible

for his setup, service and war-

ranty repair work.

Q. Whom should I contact if I have

further questions about this war-

ranty?

A. Your Yamaha snowmobile dealer

has the information and experi-

ence necessary to answer almost

any questions about this war-

ranty. If the dealer is not able to

do so, he is expected to contact

Yamaha, for clarification or

assistance.

CUSTOMER SERVICE

If your machine requires warranty ser-

vice, you must take it to any authorized

Yamaha snowmobile dealer within the

continental United States or Canada. Be

sure to bring your warranty identification

card or other valid proof of the original

date of purchase. If a question or problem

arises regarding warranty, first contact

the owner of the dealership. Since all

warranty matters are handled at the

dealer level, this person is in the best

position to help you. If you are still not

satisfied and require additional assis-

tance, please write:

FOR U.S.A. CUSTOMERS:

YAMAHA MOTOR CORPORATION,

U.S.A.
CUSTOMER RELATIONS DEPART-

MENT
P.O. Box 6555
Cypress, California 90630

FOR CANADIAN 

CUSTOMERS:

YAMAHA MOTOR CANADA LTD.
CUSTOMER RELATIONS DEPART-

MENT
480 GORDON BAKER RD
Toronto, Ontario M2H 3B4
When contacting Yamaha, be sure to

include the model, serial number, names,

dates, and receipts.

Summary of Contents for SR10LE





















































Reviews: