Yamaha SR10LE Operator'S Manual Download

Page: 18 / 52



NOTE: If the throttle control lever

operates properly and the engine

does not start, a malfunctioning moni-

tor switch may be the problem. Take

the snowmobile to an authorized

Yamaha Snowmobile dealer for ser-

vice. If not under warranty, this ser-

vice is at the discretion and expense

of the snowmobile owner. However, if

a dire emergency exists wherein the

engine must be started, disconnect

the throttle monitor switch located in

the right-side handlebar control.



NOTE: If disconnection of the throt-

tle monitor switch is needed to start

the engine, take the snowmobile to an

authorized Yamaha Snowmobile

dealer for service as soon as possi-

ble. If not under warranty, this service

is at the discretion and expense of the

snowmobile owner.



NOTE: The monitor switch is now

bypassed. All other ignition/electrical

features (ignition switch, emergency

stop switch, headlight, taillight, and

brakelight) will operate properly.

Varying Altitude

Operation

Operating a snowmobile at varying alti-

tudes requires changes in performance

components. These changes affect drive

train components. Have a Yamaha dealer

perform altitude-related service.



NOTE: Just as important as cali-

brating the snowmobile for higher alti-

tudes is recalibrating the snowmobile

when going to lower altitudes.



NOTE: Drive train changes can be

made by the snowmobile owner if

qualified to do so. If the owner does

not feel qualified, take the snowmo-

bile to an authorized Yamaha Snow-

mobile dealer for this service. This

service is at the discretion and

expense of the snowmobile owner

! WARNING

Under no circumstances should dis-

connection of the throttle control wir-

ing harness be used as a substitute

for the monitor switch during normal

operation of the snowmobile. Per-

sonal injury and damage could occur

if the throttle system malfunctions or

if the operator is unable to stop the

engine in an emergency. If the snow-

mobile must be operated with a dis-

connected throttle control wiring

harness, EXTREME CAUTION MUST

BE TAKEN. NEVER EXCEED 10 MPH

WITH THE THROTTLE CONTROL

WIRING HARNESS DISCONNECTED.

Summary of Contents for SR10LE





















































Search results

Summary of Contents for SR10LE

Reviews:

Related manuals for SR10LE

Brands by name

Popular brands

Yamaha SR10LE, Operator'S Manual

Search results

Summary of Contents for SR10LE

Reviews:

Related manuals for SR10LE

Brands by name

Popular brands