manualshive.com logo in svg

Yamaha SR10LE, Operator'S Manual

Share
Download
Yamaha SR10LE Operator'S Manual Download Page 7

5

Speedometer/

Tachometer/Digital 

Gauge

CWI-050A

A. Coolant Temperature 

Indicator

The indicator and LOW TEMP display

will cease to flash when the engine

reaches proper operating temperature.
If the coolant temperature rises too far

above proper operating temperature, the

indicator will flash a warning (alert) and

the engine will “surge” to alert the opera-

tor. If the coolant temperature rises to a

critical point above proper operating tem-

perature, the indicator will cease flashing

and will remain constantly illuminated.

NOTE: If the indicator is constantly

on, the engine will shut off if vehicle

speed  is  reduced  to  1.5  km-h  (0.9

MPH) or slower.

B. High Beam Indicator

The indicator is on whenever the high

beam mode is selected by the headlight

switch.

C. Oil Pressure Indicator

The indicator relates to engine oil pres-

sure, not the oil level; however, if the oil

level is low, it may affect oil pressure. If

oil pressure is lost, check the oil level

(see page 21).

If the indicator does not go out or if the

engine does not start, take the snowmo-

bile to an authorized Yamaha Snowmo-

bile dealer. If not under warranty, this

service is at the discretion and expense of

the snowmobile owner.

D. Low Fuel Indicator

The indicator illuminates whenever the

gas in the gas tank is low.

E. Coolant Temperature/

Battery Voltage/Intake Air 

Temperature

This bar display shows coolant tempera-

ture, battery voltage, intake air tempera-

ture, and on the 6000, exhaust

temperature. Press the Lower Left Button

to change which parameter is being dis-

played. Press and hold the Lower Left

Button to see the actual values associated

with the mode selected.

F. Fuel Level Display

This display shows the approximate

amount of gas remaining in the gas tank.

G. RPM/Speed/Clock/

Altimeter

Press the Upper Left Button to cycle the

left screen between RPM and speed.

NOTE: When RPM is displayed on

the left screen, the right screen will

display  speed,  clock,  or  altimeter.

When speed is displayed on the left

screen, the right screen will display

RPM, clock, or altimeter. 

Press the Upper Right Button to cycle the

right screen between speed, RPM, clock,

and altimeter.
Press and hold the Upper Button on the

speed-side of the gauge to shift the gauge

between standard (MPH/miles/fahren-

heit) and metric (km/h/kilometers/cel-

sius) modes.
Press and hold the Upper Button on the

RPM-side of the gauge to view maxi-

mum RPM. This value is reset each time

the ignition key is turned off.

CAUTION

If  the  indicator  is  illuminated,  stop  the

engine immediately and allow it to cool

down.  If  unable  to  either  determine  or

remedy the problem, take the snowmo-

bile to an authorized Yamaha Snowmo-

bile  dealer  for  service.  If  not  under

warranty, this service is at the discretion

and expense of the snowmobile owner.

Summary of Contents for SR10LE





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands