manualshive.com logo in svg

Yamaha SR10LE, Operator'S Manual

Share
Download
Yamaha SR10LE Operator'S Manual Download Page 13

11

Operating in Reverse

1. When shifting into reverse, always

wait for the reverse icon to illumi-

nate and the reverse alarm to sound

before backing up.

NOTE:  The  reverse  function  is  can-

celled whenever the engine is shut off.

2. After shifting from reverse to for-

ward (or from forward to reverse),

apply the throttle slowly and evenly

to allow the driven pulley to engage

properly.

Access Panel/Hood

To remove the access panel and hood, use

the following procedure:

0747-830

1. Remove the hairpin clip from the pin

located at the front of the access

panel. Move the panel up and off the

pin; then swing the panel all the way

out and unhinge the panel from the

lower console.

2. Remove the torx-head screws secur-

ing the hood (located on the underside

of the hood above the front tube of the

upper A-arm); then remove the torx-

head screws from the top-side of the

hood securing the hood to the upper

console and the torx-head screws

from under the nosepiece of the hood.

3. Remove the intake panel below the

gauge; then locate the hood harness

connector (located in front of the

speedometer) and unplug the con-

nector; then move the hood slightly

forward and remove the hood.

To install the access panel and hood, use

the following procedure:

1. Position the hood onto the snowmo-

bile and connect the hood harness

connector making sure the harness

does not become pinched.

2. Secure the hood with torx-head

screws and tighten securely.

3. Install the access panel onto the

lower console; then close the access

panel and secure with the hairpin

clip. Install the intake panel.

Removable Seat

To remove the seat, remove the torx-head

screw from the underside of the seat; then

lift on the back of the seat and move it up

and rearward to remove it.

0747-739

To install the seat, route the front tab on

the seat through the seat-base hold-down

bracket; then install the seat and secure

using the torx-head screw.

! WARNING

Use caution and minimal speed when

operating the snowmobile in reverse.

Be  sure  the  button  is  in  the  desired

position.

CAUTION

After reversing in deep powder snow

conditions,  make  sure  the  snowflap

does not become “caught up” in the

track. Track and/or snowflap damage

may occur.

CAUTION

If  the  snowmobile  is  equipped  with

ice  scratchers,  the  scratchers  must

be  disengaged  or  component  dam-

age will occur.

CAUTION

Prior  to  removing  the  seat,  lift  the

rear  of  the  seat  and  disconnect  the

seat heater harness connector.

Summary of Contents for SR10LE





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands