Yamaha SR10LE Operator'S Manual Download

Page: 9 / 52

Handlebar Tilt

The handlebar can be adjusted to the

operator’s preference. To adjust the han-

dlebar, use the following procedure:

1. Remove the handlebar cover; then

loosen the eight cap screws securing

the handlebar caps to the riser and the

riser to the steering post.

0747-828

2. Adjust the handlebar to operator’s

desired position, tighten the cap

screws evenly to 2.0 kg-m (15 ft-lb),

and check steering for maximum
right/left turning capabilities.

Exhaust System

The exhaust system is designed to reduce

noise and to improve the total perfor-

mance of the engine. If any exhaust sys-

tem component is removed from the

engine and the engine is run, severe

engine damage will result.

Air-Intake Silencer

Used in conjunction with the fuel intake

system is a specially designed air-intake

silencer. The purpose of the silencer is to

quiet the intake of fresh air. Since the fuel

intake system is calibrated with the air-

intake silencer in place, the engine must

never be run with the silencer removed.

Performance will not be improved if the

air-intake silencer is removed. In con-

trast, severe engine damage will occur.

Cooling System

These snowmobiles are equipped with a

closed liquid cooling system for engine

cooling. The cooling system should be

inspected daily for leakage and damage.

Also, the coolant level should be checked

daily. If leakage or damage is detected,

take the snowmobile to an authorized

Yamaha Snowmobile dealer for service.

If not under warranty, this service is at

the discretion and expense of the snow-

mobile owner.
When filling the cooling system, use an

ethylene glycol-based coolant/water mix-

ture which will satisfy the coldest antici-

pated weather conditions of your area in

accordance with the coolant manufac-

turer’s recommendations.



NOTE: If operating on ice or hard-

packed snow conditions, it is recom-

mended that Ice Scratchers be

installed to reduce wear strip wear

and engine overheating.

For checking/filling cooling system, refer

to Coolant Level sub-section in the Main-

tenance section.

P2300 Ignition coil A primary control circuit

low

P2303 Ignition coil B primary control circuit

low

P2306 Ignition coil C primary control circuit

low

U0155 Lost communication with the ECM

CAUTION

Do not rotate the handlebar to a posi-

tion that allows air to enter the brake

system.

! WARNING

Tighten cap screws according to

specifications to prevent unexpected

“movement” of the handlebar during

operation over rough terrain. DO NOT

position the handlebar so steering

(maximum right/left turning capabili-

ties) or throttle and brake controls

are affected.

Code

Trouble

CAUTION

These snowmobiles are not designed

to be operated in dusty conditions.

Operating the snowmobile in dusty

conditions will result in severe

engine damage.

Summary of Contents for SR10LE





















































Search results

Summary of Contents for SR10LE

Reviews:

Related manuals for SR10LE

Brands by name

Popular brands

Yamaha SR10LE, Operator'S Manual

Search results

Summary of Contents for SR10LE

Reviews:

Related manuals for SR10LE

Brands by name

Popular brands