Yamaha S03 voice editor Owner'S Manual Download Page 97

Page: 97 / 112

Appendix

Harmonic Content (Control #071)

Messages which adjust the filter resonance set for each
voice.
The value set here is an offset value which will be added
to or subtracted from the voice data.
Higher values will result in a more characteristic,
resonant sound.
Depending on the voice, the effective range may be
narrower than the range available for adjustment.

Release Time (Control #072)

Messages which adjust the EG release time set for each
voice.
The value set here is an offset value which will be added
to or subtracted from the voice data.

Attack Time (Control #073)

Messages which adjust the EG attack time set for each
voice.
The value set here is an offset value which will be added
to or subtracted from the voice data.

Brightness (Control #074)

Messages which adjust the filter cutoff frequency set for
each voice.
The value set here is an offset value which will be added
to or subtracted from the voice data.
Lower values will result in a softer sound.
Depending on the voice, the effective range may be
narrower than the range available for adjustment.

Portamento Control (Control #084)

Messages which apply a portamento between the
currently-sounding note and the subsequent note.
Portamento Control is transmitted specifying the note-on
key of the currently-sounding note.
Specify a Portamento Source Key number between 0 -
127.
When a Portamento Control message is received, the
currently sounding pitch will change with a Portamento
Time of 0 to the next note-on key on the same channel.
For example, the following settings would apply a
portamento from note C3 to C4.

90H 3CH 7FH ......... C3 Note on
B0H 54H 3CH ......... Source key number set to C3
90H 48H 7FH.......... C4 Note on (When C4 is on, C3 is

raised by a portamento to C4.)

Effect1 Depth (Reverb Send Level)
(Control #091)

Messages which adjust the send level for the Reverb
effect.

Effect3 Depth (Chorus Send Level)
(Control #093)

Messages which adjust the send level for the Chorus
effect.

Effect4 Depth (Variation Effect Send Level)
(Control #094)

Messages which adjust the send level for the Variation
effect.
If Variation effect uses System effect, this message sets
the send level for the Variation effect. If it uses Insertion
effect, this setting is invalid.

Data Increment (Control #096)
Decrement (Control #097) for RPN

Messages which increase or decrease the MSB value of
pitch bend sensitivity, fine tune, or coarse tune in steps of
1. You are required to assign one of those parameters
using the RPN in the external device in advance.
The data byte is ignored.
When the maximum value or minimum value is reached,
the value will not be incremented or decremented further.
(Incrementing the fine tune will not cause the coarse
tune to be incremented.)

NRPN (Non-Registered Parameter Number)
LSB (Control #098)
NRPN (Non-Registered Parameter Number)
MSB (Control #099)

Messages which adjust a voice’s vibrato, filter, EG, drum
setup or other parameter settings.
First send the NRPN MSB and NRPN LSB to specify the
parameter which is to be controlled. Then use Data Entry
(page 96) to set the value of the specified parameter.
Note that once the NRPN has been set for a channel,
subsequent data entry will be recognized as the same
NRPN’s value change. Therefore, after you use the
NRPN, you should set a Null (7FH, 7FH) value to avoid
an unexpected result.
The following NRPN numbers can be received.

*rr=Note number for each drum voice instrument.

PARAMETER

Vibrato Rate

Vibrato Depth

Vibrato Delay

Filter Cutoff Frequency

Filter Resonance

EG Attack Time

EG Decay Time

EG Release Time

Drum Filter Cutoff Frequency

Drum Filter Resonance