Yamaha RS7000 Ver.1.2 Service Manual Download Page 49 | Manualshive

Page: 49 / 97

background image

RS7000

49

Verify that the knob does not "catch," and that the value changes
smoothly.
There is no prescribed order in which the knobs must be turned.
If the knobs are functioning correctly, a result of OK will be
displayed in the LCD screen. The test will end, and you will be
able to select a different test item.
If a result of NG is returned during this test, refer to section "(E)
Proceeding to the next test if a result is NG" for the actions to
take.

7. Pads 1-2, foot switch

This checks whether pads 1-2 and the foot switch are operating
correctly.

(Test method)
As directed by the following LCD screen, strike pads 1--2 softly
(value: 10) or strongly (value: 110).
Connect a foot switch to the [FOOT SW] connector, and turn it
on (0) / off (1).

//// RS7000 Test Program ////

07:Pad,FootSW :Press [ENTER]

[-1] [+1]

Verify that the numbers displayed in the LCD change for pads
1--2 and for the foot switch.
There is no defined order in which these items need to be
checked.
If the pads and foot switch are functioning correctly, a result of
OK will be displayed in the LCD screen. The test will end, and
you will be able to select a different test item.
If a result of NG is returned during this test, refer to section "(E)
Proceeding to the next test if a result is NG" for the actions to
take.

8. MIDI IN/OUT A

This checks the operation of MIDI IN/OUT A by using a test
pattern (AA EF 00 55).

(Test method)
Before executing this test, use a MIDI cable to connect [MIDI
IN] and [MIDI OUT A].

The result of the test will be displayed in the LCD screen. The
test will end, and you will be able to select a different test item.

//// RS7000 Test Program ////

07:Pad,FootSW :

Pad1

:<yyy> xxx

Pad2

:<yyy> xxx

FootSw

:<yyy> xxx

[-1] [+1]

yy: target value

xx: current value

//// RS7000 Test Program ////

07:Pad,FootSW :OK

Pad1

:OK

Pad2

:OK

FootSw

:OK

[-1] [+1]

(Test result display)

OK

NG

No display

//// RS7000 Test Program ////

08:MIDI A

:Press [ENTER]

[-1] [+1]

//// RS7000 Test Program ////

06:Knob :

OK

OK OK OK OK

OK OK OK OK OK OK OK

OK

OK OK OK OK OK

OK OK

OK OK OK

[-1] [+1]

(Test result display)

OK

NG

No display

//// RS7000 Test Program ////

06:Knob :->127->0->OK

xxx xxx xxx xxx

xxx xxx xxx xxx xxx xxx xxx

xxx

xxx xxx xxx xxx xxx

xxx xxx

xxx xxx xxx

MASTER EFFECT

SEQUENCE PLAY FX

LFO

PITCH

EFFECT SEND/VOLUME

EG

FILTER

xxx: current value of each knob

«
...
47
48
49
50
51
...
»

Summary of Contents for RS7000 Ver.1.2


































































































Reviews:

No comments

Related manuals for RS7000 Ver.1.2

Brand: CAIRE Pages: 2

Brand: Rain-Flo Irrigation Pages: 20

Attest Auto-reader 390

Brand: 3M Pages: 2

Brand: 3M Pages: 2

Brand: 3M Pages: 2

PELTOR WS LiteCom Plus

Brand: 3M Pages: 7

Steri-Vac GS Series

Brand: 3M Pages: 52

Brand: Bang & Olufsen Pages: 2

Brand: Tascam Pages: 78

MINISTUDIO CREATOR US-42

Brand: Tascam Pages: 11

Brand: ZacUrate Pages: 2

Brand: ZacUrate Pages: 2

Brand: Y.I.C. TECHNOLOGIES Pages: 6

GED5000IL Series

Brand: Zimmer Pages: 52

Brand: Jefferson Pages: 2

Brand: Lighthouse Pages: 2

Brand: ultraMEDIC Pages: 28

Brand: Evermed Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands