Yamaha RS7000 Ver.1.2 Service Manual Download Page 21 | Manualshive

Page: 21 / 97

background image

RS7000

21

You can increase the RS7000’s memor y by installing
commercially available SIMMs (single in-line memory modules).
This section explains how to carry out the installation.

Installing SIMMs

• You need to use 72-pin SIMMs with access times of 70ns

or less. The SIMM module size may be 4, 8, 16, or 32 MB.
The RS7000 is designed for use with 32 bit SIMMs, but can
also accept installation of 36 bit (parity-type) SIMMs.

• When purchasing SIMMs, make sure that the SIMM design

does not utilize more than 18 memory chips per module.
(SIMMs comprised of more than 18 chips do not operate
correctly on the RS7000.)

• SIMMs must be installed as a pair of the identical capacity.

It is not possible to add just a single SIMM.

• The RS7000 ships with 4 MB of memory installed. This

means that if, for example, you install a pair of 16 MB SIMMs,
the sampling memory will be 4 + (16 x 2) = 36 MB. However,
the maximum sampling memory is 64 MB. For this reasons
the original memory will effectively be disabled if you install
a pair of 32 MB SIMMs (one pair: 32 x 2 = 64 MB).

• YAMAHA recommends that you purchase SIMMs that

conform to the JEDEC* standard. Please be aware,
however, that conformance to this standard does not
guarantee that the SIMM will oper-ate on the RS7000 even
if it operates on a personal computer.
* JEDEC (Joint Electron Device Engineering Council) sets

standards for terminal configurations within electronic
devices.

IMPORTANT

«
...
19
20
21
22
23
...
»

Summary of Contents for RS7000 Ver.1.2


































































































Reviews:

No comments

Related manuals for RS7000 Ver.1.2

Brand: Rath Pages: 3

Brand: Salvis Pages: 40

Brand: IDEAL Pages: 2

Brand: Labnet Pages: 2

Brand: Nakayama Pages: 37

Brand: Eaton Pages: 21

Brand: NANO Pages: 4

Brand: Omlet Pages: 2

Brand: Omicron Pages: 382

Brand: Omicron Pages: 188

Brand: P-Q Controls Pages: 5

Brand: P+L Systems Pages: 2

RIDA qLine ZG2601

Brand: R-Biopharm Pages: 23

Brand: Velp Scientifica Pages: 16

Brand: Velp Scientifica Pages: 2

Brand: Velp Scientifica Pages: 32

Brand: Velleman-Kit Pages: 32

Wallach UltraFreeze

Brand: Cooper Surgical Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands