Yamaha RS7000 Ver.1.2 Service Manual Download Page 23

Page: 23 / 97

RS7000

4. Replace the bottom cover.
5. Plug in the power cord.

• To verify that the installed SIMMs are detected correctly,

hold down [SHIFT] and press [UTILITY] to access the
FREE MEM-ORY display.

The optional AIEB2 Input/Output expansion board adds digital
I/O (both optical and coaxial formats) and six assignable outputs
to the RS7000.

Procedure

1. Be sure that you have the following at hand before starting

the installation.

• AIEB2 I/O expansion board: Confirm that there are 3

cables extending from the board.

• Phillips screwdriver: Magnetic-tipped screwdriver is

recommended.

• Workbench: Please carr y out all work on a stable

workbench or table. Spreading a cloth over the work surface
will help prevent scratching.

• Gloves: Be sure to wear gloves so that your hands are not

scratched by the metal cover or other metal parts.

2. Remove the bottom cover.
3. Remove the three screws (B) from the rear panel, and remove

the I/O cover.

• The I/O cover may fall down when all three screws are

removed, so be sure to hold the I/O cover with one hand
while removing the screws.

• The I/O cover you removed will not be needed as long as

the AIEB2 is installed, but the screws with which it was
attached will be used to attach the AIEB2, so be careful not
to misplace them.

• These screws (B) are of a different type than the twelve

screws that fasten the bottom cover. Be careful not to
confuse them with the bottom cover screws. The unit may
be damaged if you use the incorrect screws.

Installing the AIEB2 I/O Expansion Board

CAUTION

Please note that the AIEB1 cannot be used in the RS7000.

IMPORTANT

Summary of Contents for RS7000 Ver.1.2


































































































Search results

Summary of Contents for RS7000 Ver.1.2

Reviews:

Related manuals for RS7000 Ver.1.2

Brands by name

Popular brands

Yamaha RS7000 Ver.1.2, Service Manual

Search results

Summary of Contents for RS7000 Ver.1.2

Reviews:

Related manuals for RS7000 Ver.1.2

Brands by name

Popular brands