Yamaha RS7000 Ver.1.2 Service Manual Download Page 22 | Manualshive

Page: 22 / 97

background image

RS7000

22

Procedure

1. Be sure that you have the following at hand before starting

the installation.

• SIMMs (one pair: 2 modules)
• Phillips screwdriver: Magnetic-tipped screwdriver is

recommended.

• Workbench: Please carry out all work on a stable

workbench or table. Spreading a cloth over the work surface
will help prevent scratching.

• Gloves: Be sure to wear gloves so that your hands are not

scratched by the metal cover or other metal parts.

2. Remove the bottom cover.
3. Insert the SIMM module into the socket on the circuit board.

• First identify the sockets that you will install the SIMM into.

• Hold the SIMM with its cutout part facing the rear panel, and

set the SIMM into the socket at an angle as shown in the
figure below (1). Then push the SIMM upright until it clicks
into the position shown in figure (2), locking it into place.

Sockets for SIMM installation

• Repeat this step for the other SIMM.
• If you need to remove a SIMM from a socket, hold open

the two hooks on the socket (one at each end), push on
the SIMM to tilt it downward, and then pull it out.

This completes the installation.
If you wish to install an I/O expansion board, continue with the I/
O expansion board installation procedure.

When inserting SIMMs, always begin with the outer socket
(i.e., the socket closest to the side of the RS7000 cover).
SIMMs will not fit into the socket if you reverse this order.

NOTE

(1)

(2)

«
...
20
21
22
23
24
...
»

Summary of Contents for RS7000 Ver.1.2


































































































Reviews:

No comments

Related manuals for RS7000 Ver.1.2

Brand: Calistair Pages: 44

Brand: GBC Pages: 8

Brand: KAPSCH Pages: 57

Coronis 5MP Mammo

Brand: Barco Pages: 4

Brand: Barco Pages: 167

Color Coronis 2MP

Brand: Barco Pages: 156

Color Coronis 2MP

Brand: Barco Pages: 12

Brand: Barco Pages: 39

Brand: Barco Pages: 158

Brand: Nektar Pages: 3

Brand: Youkey Pages: 86

Brand: Wacker Neuson Pages: 62

Brand: Warehouse-lighting Pages: 3

Brand: Eagle Group Pages: 8

Brand: E2S Pages: 5

Brand: Hakko Electronics Pages: 8

Professional HS 8

Brand: Hailo Pages: 5

Brand: Hainbuch Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands