Yamaha RS7000 Ver.1.2 Service Manual Download Page 68 | Manualshive

Page: 68 / 97

background image

RS7000

68

Other Messages (Not Errors)

Are you sure? NO[F2]/
YES[F3]

Confirms that you want to execute a specified operation. Press [F2] or [F3] as
required.

Can’t Undo. Cancel [F2]/OK
[F3]

When some jobs are executed the internal memory becomes full and undo
cannot be used. Press [F3] if this is OK, or [F2] to abort the operation. Try again
after erasing unwanted songs, patterns, or user phrases.

Completed

The specified load, save, format, or other job has been completed.

Executing …

A format operation or job is being executed. Please wait.

Loading ... (xxxxxxxx)
Abort [F3]

Appears when a file is being loaded. Press [F3] to abort the load operation.

Overwrite? NO[F2]/YES[F3]

A save operation will overwrite data on the card or disk, and this message con-
firms whether it is OK to continue. Press [F2] or [F3] as required.

Overwrite Sample Voice?
Cancel [F2]/OK [F3]

When executing Create after Realtime Loop Remix this message confirms
whether it is OK to overwrite the sample voice in the current track. Press [F3] to
overwrite, or [F2] to abort.

Saving ... (xxxxxxxx)
Abort [F3]

Appears when a file is being saved. Press [F3] to abort the save operation.

Same Common Sample Voice
Number. Skip All [F2]/Renum-
ber [F3]

Appears when a pattern or song which uses common sample voices is loaded
and a common sample voice will be loaded into a number which already con-
tains data. Press [F2] skip loading the common sample voice data, or [F3] load
the data after renumbering the voice.

Sequence or Sample Voice
Exists. Cancel [F2]/
Replace [F3]

Appears when sequence or sample data already exists in a track selected in
the sampling setup display.

«
...
66
67
68
69
70
...
»

Summary of Contents for RS7000 Ver.1.2


































































































Reviews:

No comments

Related manuals for RS7000 Ver.1.2

Brand: Wavetek Pages: 74

Brand: Fairchild Pages: 16

Brand: Banfer Pages: 6

Brand: Nautilus Pages: 17

Brand: National Instruments Pages: 6

TUV COMFORT LIGHT Series

Brand: olympia electronics Pages: 4

Brand: Softing IT Networks Pages: 54

Brand: Velp Scientifica Pages: 123

Brand: IKA Pages: 48

Brand: Chauvin Arnoux Pages: 12

Brand: EMIT Pages: 6

Turbo Jet 10 i-CON

Brand: Stocks AG Pages: 30

Randell DROP-IN 9550-290

Brand: Unified Brands Pages: 16

Brand: E-LINK Pages: 4

Unidrill-W Series

Brand: Moore Pages: 46

E-Luminexx Vascular Stent

Brand: Bard Pages: 104

Brand: sticklett Pages: 2

Brand: SHOWTEC Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands