Yamaha Rhino YXR66FAV Owner'S Manual Download

Page: 42 / 163

4-19

EVU00310

Fuel level check window

The amount of fuel in the fuel tank can be
checked through the fuel level check window.
If the fuel level is low, refuel as soon as possi-
ble.

1. Fuel level check window

EVU00320

Starter (choke) “

”

Starting a cold engine requires a richer air-fuel
mixture. A separate starter circuit supplies this
mixture.
Move in direction

to turn on the starter

(choke).
Move in direction

to turn off the starter

(choke).
Refer to “Starting a cold engine” for proper op-
eration. (See pages 6-1–6-3.)

A. Starter (choke) “

”

1. Fully open

2. Half open

3. Closed

U5UG12.book Page 19 Thursday, June 23, 2005 9:02 AM

Summary of Contents for Rhino YXR66FAV




































































































































































Search results

Summary of Contents for Rhino YXR66FAV

Reviews:

Related manuals for Rhino YXR66FAV

Brands by name

Popular brands

Yamaha Rhino YXR66FAV, Owner'S Manual

Search results

Summary of Contents for Rhino YXR66FAV

Reviews:

Related manuals for Rhino YXR66FAV

Brands by name

Popular brands