Yamaha Rhino YXR66FAV Owner'S Manual Download

Page: 110 / 163

8-18

CAUTION:

Mix anti freeze with distilled water only.
However, if distilled water is not available,
soft water may be used for refilling.

Changing the coolant

The coolant must be changed by a Yamaha
dealer at the intervals specified in the periodic
maintenance and lubrication chart.

NOTE:

●

Adding water instead of coolant lowers
the antifreeze content of the coolant. If
water is used instead of coolant, have a
Yamaha dealer check the antifreeze con-
tent of the coolant as soon as possible.

●

The radiator fan operation is completely
automatic. It is switched on or off accord-
ing to the coolant temperature in the radi-
ator.

If your vehicle overheats, see page 8-54 for
details.

EVU00740

Axle boots

Check the protective boots for holes or tears.
If any damage is found, have them replaced
by a Yamaha dealer.

1. Front axle boot (

2 each side)

U5UG12.book Page 18 Thursday, June 23, 2005 9:02 AM

Summary of Contents for Rhino YXR66FAV




































































































































































Search results

Summary of Contents for Rhino YXR66FAV

Reviews:

Related manuals for Rhino YXR66FAV

Brands by name

Popular brands

Yamaha Rhino YXR66FAV, Owner'S Manual

Search results

Summary of Contents for Rhino YXR66FAV

Reviews:

Related manuals for Rhino YXR66FAV

Brands by name

Popular brands