Yamaha Rhino YXR66FAV Owner'S Manual Download

Page: 128 / 163

8-36

EVU00870

Parking brake lever free play adjustment

Periodically check the parking brake lever free
play and adjust it if necessary.

1. Shift the drive select lever into low gear

“L”.

2. Remove the seats. (See page 4-20 for

seat removal and installation proce-
dures.)

3. Remove the console. (See page 8-8 for

console removal and installation proce-
dures.)

4. Check the parking brake lever free play.

The maximum free play is equal to one
click of the parking brake lever. If neces-
sary, adjust the free play as follows.

a. Parking brake lever free play

NOTE:

The parking brake lever must be released
when checking and adjusting the parking
brake lever free play.

5. Loosen the locknut.

U5UG12.book Page 36 Thursday, June 23, 2005 9:02 AM

Summary of Contents for Rhino YXR66FAV




































































































































































Search results

Summary of Contents for Rhino YXR66FAV

Reviews:

Related manuals for Rhino YXR66FAV

Brands by name

Popular brands

Yamaha Rhino YXR66FAV, Owner'S Manual

Search results

Summary of Contents for Rhino YXR66FAV

Reviews:

Related manuals for Rhino YXR66FAV

Brands by name

Popular brands