Yamaha Rhino YXR66FAV Owner'S Manual Download | Manualshive

Page: 38 / 163

background image

4-15

NOTE:

_

●

If the differential gear lock is not engag-
ing properly, turn the steering wheel back
and forth to help it engage.

●

Riding before the differential gear lock is
properly engaged will cause the engine
speed to be limited until engagement is
complete.

For special edition models:

●

When the switch is set to “LOCK”, the dif-
ferential gear lock indicator light will flash
until the differential gear is locked.

●

When the indicator light is flashing, turn-
ing the steering wheel back and forth will
help the differential gear lock to engage.

●

Riding before the differential gear lock is
properly engaged (e.g., when the indica-
tor light is flashing) will cause the engine
speed to be limited until engagement is
complete.

_

EVU00260

Accelerator pedal

Press the accelerator pedal down to increase
engine speed. Spring pressure returns the
pedal to the rest position when released. Al-
ways check that the accelerator pedal returns
normally before starting the engine.

1. Accelerator pedal

U5UG12.book Page 15 Thursday, June 23, 2005 9:02 AM

«
...
36
37
38
39
40
...
»

Summary of Contents for Rhino YXR66FAV




































































































































































Reviews:

No comments

Related manuals for Rhino YXR66FAV

Brand: E-Z-GO Pages: 158

Brand: TYPHOON Pages: 28

Brand: AC Air Technology Pages: 49

Brand: Iron Baltic Pages: 24

Brand: PRONAR Pages: 99

Brand: Yamaha Pages: 92

Brand: Jeep Pages: 16

Brand: Ifor Williams Trailers Pages: 16

Brand: Toro Pages: 12

500 MXU IRS 4X4 NAKED EFI

Brand: KYMCO Pages: 1

Brand: Metal Motorsports Pages: 54

Brand: SCORPION Pages: 32

Brand: Sodi Pages: 50

All Terrain AT200 TOW

Brand: MasterMover Pages: 28

Brand: CROSSRUNNER Pages: 20

Brand: Bearcat Pages: 164

Brand: AVANT Pages: 6

Brand: AVANT Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands