background image

 

Trouble Recovery

 

92

 

EMU29671

 

Engine fails to operate

 

EMU29742

 

Low oil level alert activates

 

If the oil level is allowed to drop too low, the
red segment will appear on the oil level indi-
cator, the buzzer will sound, and engine
speed will be limited to about 2000 r/min. If
this happens, a reserve amount of oil can be
pumped from the remote oil tank to the en-
gine oil tank using the emergency switch.

WARNING

 

EWM01050 

 

Be sure to stop the engine before per-

 

forming this procedure.

NOTICE

 

ECM00901 

 

 

If the emergency switch is held up too
long, too much oil will be pumped into
the engine oil tank, overflowing it. Re-
lease the switch when oil reaches the
upper level line on the engine oil tank.

 

 

Do not use this emergency procedure
unless the oil level-alert indicators are

 

working.

 

1.

Remove the top cowling.

2.

Turn on the main switch.

3.

Lift the emergency switch to pump re-
serve oil into the engine oil tank from the
remote oil tank.

4.

After using the emergency switch, turn
off the main switch, then turn it back on.
This resets the alert system to normal
operation. The yellow segment will con-
tinue to be displayed on the oil level indi-
cator.

5.

Start the engine and return to the near-
est port for more oil.

TIP:

 

 

The maximum reserve oil capacity is 1500
cm

 

3

 

 (1.6 US qt, 1.31 Imp qt).

 

 

The oil-feed pump will not operate if the
engine is tilted up more than 35°. Put the
engine in the upright position (not tilted)
before using the emergency switch.

ON START

OFF

ZMU01906

 

1. Emergency switch

1. Engine oil tank
2. Remote oil tank

1

ZMU04010

1

2

ZMU01908

✩✫✳✬✤✲ ✬✥   

©

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for LZ200











































































































Reviews: