Yamaha LZ200 Operator'S Manual Download Page 70

Page: 70 / 106

Operation

Models equipped with trim rods: Once
the outboard motor is supported with the
tilt support lever, press the power trim
and tilt switch “

” (down) to retract the

trim rods.

NOTICE:

Be sure to retract

the trim rods completely during
mooring. This protects the rods from
marine growth and corrosion which
could damage the power trim and tilt
mechanism.

[ECM00251]

EMU33121

Procedure for tilting down (power
trim and tilt models)

Push the power trim and tilt switch “

”

(up) until the outboard motor is support-
ed by the tilt rod and the tilt support lever
becomes free.

Release the tilt support lever.

Push the power trim and tilt switch “

”

(down) to lower the outboard motor to
the desired position.

ZMU03996

ZMU03997

ZMU03998

ZMU01936

ZMU04603

✩✫✳✬✤✲ ✩✧

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for LZ200











































































































Search results

Summary of Contents for LZ200

Reviews:

Related manuals for LZ200

Brands by name

Popular brands

Yamaha LZ200, Operator'S Manual

Search results

Summary of Contents for LZ200

Reviews:

Related manuals for LZ200

Brands by name

Popular brands