Yamaha KODIAK 700 2018 Page 119 Owner'S Manual Download

Page: 119 / 180

8-21

7. Insert the dipstick completely into the oil filler

hole.

8. Install the access cover by turning it clock-

wise.

To change the engine oil (with or without oil fil-
ter cartridge replacement)

1. Park the ATV on a level surface.
2. Start the engine, warm it up for several min-

utes, and then turn it off.

3. Remove the access cover by turning it coun-

terclockwise.

4. Place an oil pan under the engine to collect

the used oil.

5. Remove the dipstick, and then remove the

engine oil drain bolt and its gasket to drain the
oil from the crankcase.

TIP

Skip steps 6–10 if the oil filter cartridge is not be-
ing replaced.

6. Remove panel F. (See page 8-9.)
7. Remove the oil filter cartridge with an oil filter

wrench.

1. Engine oil drain bolt
2. Gasket

UB5K60E0.book Page 21 Monday, May 28, 2018 11:35 AM

Summary of Contents for KODIAK 700 2018





















































































































































































Search results

Summary of Contents for KODIAK 700 2018

Reviews:

Related manuals for KODIAK 700 2018

Brands by name

Popular brands

Yamaha KODIAK 700 2018, Owner'S Manual

Search results

Summary of Contents for KODIAK 700 2018

Reviews:

Related manuals for KODIAK 700 2018

Brands by name

Popular brands