Yamaha KODIAK 700 2018 Page 139 Owner'S Manual Download | Manualshive

Page: 139 / 180

background image

8-41

8

EBU29704

Adjusting the throttle lever free play

Periodically check the throttle lever free play and
adjust if necessary.

1. Slide the rubber cover back.
2. Loosen the locknut.

3. To increase the throttle lever free play, turn

the throttle lever free play adjusting bolt in di-
rection (a). To decrease the throttle lever free
play, turn the adjusting bolt in direction (b).

4. Tighten the locknut.
5. Slide the rubber cover to its original position.

EBU24061

Valve clearance

The valve clearance changes with use, resulting in
improper air-fuel mixture and/or engine noise. To
prevent this from occurring, the valve clearance
must be adjusted by a Yamaha dealer at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

EBU29602

Brakes

Replacement of brake components requires pro-
fessional knowledge. Brake service should be
performed by a Yamaha dealer.

WARNING

EWB02572

Operating with improperly serviced or adjust-
ed brakes could lead to a loss in braking ability
and an accident.

1. Rubber cover
2. Throttle lever free play adjusting bolt
3. Locknut
4. Throttle lever free play

Throttle lever free play:

3.0–5.0 mm (0.12–0.20 in)

2WD

4WD

3

2

1

4

(b)

(a)

UB5K60E0.book Page 41 Monday, May 28, 2018 11:35 AM

«
...
137
138
139
140
141
...
»

Summary of Contents for KODIAK 700 2018





















































































































































































Reviews:

No comments

Related manuals for KODIAK 700 2018

Brand: Jianshe Pages: 82

Turbo-Max 6100 Series

Brand: SAC Pages: 66

YUM1A UMAX RALLY 2021

Brand: Yamaha Pages: 76

Brand: Yamaha Pages: 158

GRIZZLY YFM70GPAP 2023

Brand: Yamaha Pages: 180

KODIAK ULTRAMATIC YFM400FWAN 2000

Brand: Yamaha Pages: 184

Brand: gio Pages: 20

Brand: Tomberlin Pages: 142

Brand: PRONAR Pages: 99

Engine Drive AY20

Brand: Miller Electric Pages: 2

Brand: Trail Rover Pages: 34

ESCALATE TRAILER ET 12000

Brand: Bil-Jax Pages: 20

Brand: Galaxy vans Pages: 60

Brand: Yamaha Pages: 497

150GKA-2 Series

Brand: Kandi USA Pages: 16

Brand: Mahindra Pages: 79

Brand: KAYO MOTOR Pages: 91

Brand: Yamaha Pages: 180

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands