Yamaha KODIAK 700 2018 Page 144 Owner'S Manual Download

Page: 144 / 180

8-46

5. Loosen the brake cable adjuster locknut.
6. To increase the brake lever free play, turn the

brake lever free play adjusting nut in direction
(a). To decrease the brake lever free play, turn
the adjusting nut in direction (b).

7. Tighten the brake cable adjuster locknut.
8. Slide the rubber cover to its original position.
9. Tighten the locknut at the brake lever.

Adjusting the brake pedal free play

Measure the brake pedal free play as shown.

If the free play is incorrect, adjust it as follows.

1. Remove panel G.
2. Loosen the locknut.

1. Brake cable adjuster locknut
2. Brake lever free play adjusting nut
3. Rubber cover

(a)

(b)

1. Brake pedal free play

Brake pedal free play:

12.0–17.0 mm (0.47–0.67 in)

UB5K60E0.book Page 46 Monday, May 28, 2018 11:35 AM

Summary of Contents for KODIAK 700 2018





















































































































































































Search results

Summary of Contents for KODIAK 700 2018

Reviews:

Related manuals for KODIAK 700 2018

Brands by name

Popular brands

Yamaha KODIAK 700 2018, Owner'S Manual

Search results

Summary of Contents for KODIAK 700 2018

Reviews:

Related manuals for KODIAK 700 2018

Brands by name

Popular brands