Yamaha KODIAK 700 2018 Page 143 Owner'S Manual Download

Page: 143 / 180

8-45

Adjusting the brake lever free play

Measure the brake lever free play as shown.

If the free play is incorrect, adjust it as follows.

1. Loosen the locknut at the brake lever.

2. To increase the brake lever free play, turn the

brake lever free play adjusting bolt in direction
(a). To decrease the brake lever free play, turn
the adjusting bolt in direction (b).

TIP

If the specified brake lever free play could be ob-
tained as described above, skip steps 3–8.

3. Fully turn the adjusting bolt in direction (a) to

loosen the brake cable.

4. Slide the rubber cover back.

1. Brake lever free play

Brake lever free play:

6.0-7.0 mm (0.24-0.28 in)

1. Locknut
2. Brake lever free play adjusting bolt

(a)

(b)

1 2

UB5K60E0.book Page 45 Monday, May 28, 2018 11:35 AM

Summary of Contents for KODIAK 700 2018





















































































































































































Search results

Summary of Contents for KODIAK 700 2018

Reviews:

Related manuals for KODIAK 700 2018

Brands by name

Popular brands

Yamaha KODIAK 700 2018, Owner'S Manual

Search results

Summary of Contents for KODIAK 700 2018

Reviews:

Related manuals for KODIAK 700 2018

Brands by name

Popular brands