Yamaha GRIZZLY 350 YFM350AA Owner'S Manual Download | Manualshive

Page: 110 / 136

background image

8-32

8

d. Tighten the locknut at the brake lever.

TIP

When adjusting the rear brake lever free play:

●

Be sure not to step on the brake pedal.

●

Make sure the brake pedal does not move.

3.

Checking the brake pedal height

The top of the brake pedal should be posi-
tioned 72.0–82.0 mm (2.83–3.23 in) above
the footboard bracket. If the brake pedal
height is incorrect, have a Yamaha dealer ad-
just it.

EBU24754

Brake light switches

The brake light, which is activated by the brake
pedal and brake levers, should come on just be-
fore braking takes effect.
The brake light switch for the brake pedal can be
adjusted as follows, but the other brake light
switches should be adjusted by a Yamaha dealer.

1. Remove panel A. (See page 8-9.)
2. Turn the brake light switch adjusting nut while

holding the brake light switch in place. To
make the brake light come on earlier, turn the
adjusting nut in direction (a). To make the
brake light come on later, turn the adjusting
nut in direction (b).

1. Locknut

2. Brake lever free play adjusting bolt

1

2

(a)

(b)

1. Distance between brake pedal and footboard bracket

1

1

U5WH67E0.book Page 32 Thursday, June 3, 2010 2:10 PM

«
...
108
109
110
111
112
...
»

Summary of Contents for GRIZZLY 350 YFM350AA









































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM350AA

Brand: Yamaha Pages: 59

Brand: Landoll Pages: 76

Brand: Can-Am Pages: 58

1970 SKI-DADDLER

Brand: AMF Pages: 74

Utility Vehicle Workshop

Brand: Bush Hog Pages: 11

Brand: Vermeer Pages: 88

Street Rider 150MRX

Brand: Texas Pages: 33

Brand: Texas Pages: 49

Brand: Hsun Pages: 100

Brand: Humbaur Pages: 4

ST SHUTTLE 4/6 E 2008

Brand: E-Z-GO Pages: 66

Brand: Parklands Pages: 66

Brand: Samsung Pages: 54

Brand: Samsung Pages: 172

Brand: Morgan Olson Pages: 2

500 MXU IRS 4X4 NAKED EFI

Brand: KYMCO Pages: 1

Can-Am DS 450 EFI 2009

Brand: BRP Pages: 19

Brand: Yamaha Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands