Yamaha GRIZZLY 350 YFM350AA Owner'S Manual Download

Page: 123 / 136

8-45

EBU25751

Troubleshooting chart

Check the fuel level in
the fuel tank.

1. Fuel

There is enough fuel.

There is no fuel.

Check the compression.

Supply fuel.

The engine does not start.
Check the compression.

Operate the electric starter.

2. Compression

There is compression.

There is no compression.

Check the ignition.

Have a Yamaha dealer
check the ATV.

Remove the spark plug
and check the electrodes.

3. Ignition

Wipe off with a dry cloth and correct the
spark plug gap, or replace the spark plug.

Have a Yamaha dealer check the ATV.

The engine does not start.
Have a Yamaha dealer
check the ATV.

The engine does not start.
Check the battery.

Operate the electric starter.

4. Battery

The engine turns over
quickly.

The engine turns over
slowly.

The battery is good.

Check the battery lead connections,
and charge the battery if necessary.

Dry

Wet

Open the throttle halfway and operate
the electric starter.

U5WH67E0.book Page 45 Thursday, June 3, 2010 2:10 PM

Summary of Contents for GRIZZLY 350 YFM350AA









































































































































Search results

Summary of Contents for GRIZZLY 350 YFM350AA

Reviews:

Related manuals for GRIZZLY 350 YFM350AA

Brands by name

Popular brands

Yamaha GRIZZLY 350 YFM350AA, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 350 YFM350AA

Reviews:

Related manuals for GRIZZLY 350 YFM350AA

Brands by name

Popular brands