Yamaha GRIZZLY 350 YFM350AA Owner'S Manual Download Page 95

Page: 95 / 136

8-17

To change the final gear oil

1. Place the ATV on a level surface.
2. Remove the final gear case guard by remov-

ing the bolts.

3. Place an oil pan under the final gear case to

collect the used oil.

4. Remove the final gear oil filler bolt, the final

gear oil drain bolt, and their gasket to drain the
oil from the final gear case.

5. Install the drain bolt and its new gasket, and

then tighten the bolt to the specified torque.

6. Refill with the recommended final gear oil to

the brim of the filler hole as shown.

NOTICE:

Be sure no foreign material enters the final
gear case.

[ECB00421]

1. Final gear case guard
2. Bolt

1. Final gear oil drain bolt

2. Gasket

Tightening torque:

Final gear oil drain bolt:

23 Nm (2.3 m·kgf, 17 ft·lbf)

U5WH67E0.book Page 17 Thursday, June 3, 2010 2:10 PM

Summary of Contents for GRIZZLY 350 YFM350AA









































































































































Search results

Summary of Contents for GRIZZLY 350 YFM350AA

Reviews:

Related manuals for GRIZZLY 350 YFM350AA

Brands by name

Popular brands

Yamaha GRIZZLY 350 YFM350AA, Owner'S Manual

Search results

Summary of Contents for GRIZZLY 350 YFM350AA

Reviews:

Related manuals for GRIZZLY 350 YFM350AA

Brands by name

Popular brands