Yamaha GRIZZLY 350 YFM350AA Owner'S Manual Download | Manualshive

Page: 36 / 136

background image

4-11

4

ON

With the fuel cock lever in this position, fuel flows
to the carburetor. Turn the fuel cock lever to this
position when starting the engine and riding.

RES

This indicates reserve. With the fuel cock lever in
this position, the fuel reserve is made available.
Turn the fuel cock lever to this position if you run
out of fuel while riding. When this occurs, refuel as
soon as possible and be sure to turn the fuel cock
lever back to “ON”!

EBU18850

Starter (choke) “

”

Starting a cold engine requires a richer air-fuel mix-
ture, which is supplied by the starter (choke).
Move the starter (choke) in direction (a) to turn on
the starter (choke).

1. Arrow mark pointing to “ON”

1. Arrow mark pointing to “RES”

U5WH67E0.book Page 11 Thursday, June 3, 2010 2:10 PM

«
...
34
35
36
37
38
...
»

Summary of Contents for GRIZZLY 350 YFM350AA









































































































































Reviews:

No comments

Related manuals for GRIZZLY 350 YFM350AA

Brand: J&M Pages: 26

Brand: Landoll Pages: 64

BIG BEAR YFM400NN

Brand: Yamaha Pages: 161

BIG BEAR YFM400NC

Brand: Yamaha Pages: 162

BANSHEE YFZ350Y

Brand: Yamaha Pages: 142

Big Bear 400 YFM40FBB

Brand: Yamaha Pages: 156

Brand: Yamaha Pages: 156

BEARTRACKER YFM250XN

Brand: Yamaha Pages: 156

Brand: Yamaha Pages: 140

Brand: Yamaha Pages: 167

BIG BEAR YFM400FWS

Brand: Yamaha Pages: 173

BANSHEE 350 YFZ350Z

Brand: Yamaha Pages: 146

Brand: Yamaha Pages: 163

Brand: Yamaha Pages: 170

BANSHEE 350 YFZ350A

Brand: Yamaha Pages: 148

Brand: Yamaha Pages: 176

BANSHEE YFZ350R

Brand: Yamaha Pages: 168

BANSHEE YFZ350P

Brand: Yamaha Pages: 168

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands