background image

INSTRUMENT AND CONTROL FUNCTIONS

4-2

4

To unlock the steering

Push the key in, and then turn it to
“OFF” while still pushing it.

EAU49391

Indicator lights and warning 
lights 

EAU11020

Turn signal indicator light “

” 

This indicator light flashes when the
turn signal switch is pushed to the left or
right.

EAU11060

Neutral indicator light “

” 

This indicator light comes on when the
transmission is in the neutral position.

EAU11080

High beam indicator light “

” 

This indicator light comes on when the
high beam of the headlight is switched
on.

EAU11254

Oil level warning light “

” 

This warning light comes on if the en-
gine oil level is low.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. The warning light should come
on for a few seconds, and then go off.
If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.

TIP

Even if the oil level is sufficient, the
warning light may flicker when
riding on a slope or during sudden
acceleration or deceleration, but
this is not a malfunction.

This model is also equipped with a
self-diagnosis device for the oil
level detection circuit. If a problem
is detected in the oil level detection

1. Push.
2. Turn.

1

2

1. Turn signal indicator light “

2. Neutral indicator light “

3. High beam indicator light “

4. Engine trouble warning light “

5. Oil level warning light “

6. Coolant temperature warning light “

1

2 3 4

5

6

U39P11E0.book  Page 2  Monday, August 1, 2011  5:00 PM

Summary of Contents for FZ8NB













































































































Reviews: