Yamaha FZ8NB Owner'S Manual Download | Manualshive

Page: 65 / 108

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-21

7

EAU22081

Adjusting the clutch lever free
play

The clutch lever free play should mea-
sure 10.0–15.0 mm (0.39–0.59 in) as
shown. Periodically check the clutch le-
ver free play and, if necessary, adjust it
as follows.
To increase the clutch lever free play,
turn the clutch lever free play adjusting
bolt in direction (a). To decrease the
clutch lever free play, turn the adjusting
bolt in direction (b).

TIP

If the specified free play cannot be ob-
tained as described above or if the
clutch does not operate correctly, have
a Yamaha dealer check the internal
clutch mechanism.

EAU37913

Checking the brake lever free
play

There should be no free play at the
brake lever end. If there is free play,
have a Yamaha dealer inspect the
brake system.

WARNING

EWA14211

A soft or spongy feeling in the brake
lever can indicate the presence of air
in the hydraulic system. If there is air
in the hydraulic system, have a
Yamaha dealer bleed the system be-
fore operating the vehicle. Air in the
hydraulic system will diminish the

1. Clutch lever free play adjusting bolt

2. Clutch lever free play

1. No brake lever free play

1

U39P11E0.book Page 21 Monday, August 1, 2011 5:00 PM

«
...
63
64
65
66
67
...
»

Summary of Contents for FZ8NB













































































































Reviews:

No comments

Related manuals for FZ8NB

Brand: CF MOTO Pages: 443

Brand: Jialing Honda Pages: 10

Brand: R&G Pages: 47

Brand: Miller Pages: 12

Brand: Androware Pages: 2

Brand: Romet Pages: 52

Brand: Yamaha Pages: 220

Brand: Yamaha Pages: 402

Brand: Yamaha Pages: 402

Brand: Yamaha Pages: 176

Brand: Aim Pages: 47

Brand: KOOFU Pages: 24

Element Ready TMS69BL14

Brand: Rockford Fosgate Pages: 8

Brand: Benelli Pages: 314

Brand: Benelli Pages: 314

Brand: Livall Pages: 10

Brand: Honda Pages: 146

Brand: hepco & becker Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands