Yamaha FZ8NB Owner'S Manual Download

Page: 76 / 108

PERIODIC MAINTENANCE AND ADJUSTMENT

7-32

is turned to “OFF”, then con-
nect the positive lead before
connecting the negative lead.

[ECA16840]

4. After installation, make sure that

the battery leads are properly con-
nected to the battery terminals.

NOTICE

ECA16530

Always keep the battery charged.
Storing a discharged battery can
cause permanent battery damage.

EAU47134

Replacing the fuses

The main fuse, the fuel injection system
fuse, and the fuse box, which contains
the fuses for the individual circuits, are
located under the rider seat. (See page
4-14.)

TIP

To access the fuel injection system
fuse, remove the starter relay cover by
pulling it upward.

1. Main fuse

2. Fuse box

3. Fuel injection system fuse
4. Fuel injection system spare fuse

1. Fuse box
2. Headlight fuse

3. Ignition fuse

4. Signaling system fuse
5. Backup fuse (for clock)

6. Right radiator fan fuse

7. Left radiator fan fuse
8. Spare fuse

3 4 5 6 7

U39P11E0.book Page 32 Monday, August 1, 2011 5:00 PM

Summary of Contents for FZ8NB













































































































Search results

Summary of Contents for FZ8NB

Reviews:

Related manuals for FZ8NB

Brands by name

Popular brands

Yamaha FZ8NB, Owner'S Manual

Search results

Summary of Contents for FZ8NB

Reviews:

Related manuals for FZ8NB

Brands by name

Popular brands