Yamaha FZ8NB Owner'S Manual Download

Page: 84 / 108

PERIODIC MAINTENANCE AND ADJUSTMENT

7-40

5. Turn the drive chain slack adjust-

ing bolts fully in direction (a) and
push the wheel forward.

6. Remove the drive chain from the

rear sprocket.

TIP

●

If the drive chain is difficult to re-
move, remove the wheel axle first,
and then lift the wheel upward
enough to remove the drive chain
from the rear sprocket.

●

The drive chain cannot be disas-
sembled.

7. While supporting the brake caliper

bracket, pull the wheel axle out,
and then remove the wheel.

NOTICE:

Do not apply the brake

after the wheel has been re-
moved together with the brake
disc, otherwise the brake pads
will be forced shut.

[ECA11071]

EAU39413

To install the rear wheel

1. Install the wheel and the brake cal-

iper bracket by inserting the wheel
axle from the left-hand side.

TIP

●

Make sure that the slot in the brake
caliper bracket is fit over the retain-
er on the swingarm.

●

Make sure that there is enough
space between the brake pads be-
fore installing the wheel.

2. Install the drive chain onto the rear

sprocket.

3. Install the axle nut.
4. Lower the rear wheel so that it is

on the ground, and then put the
sidestand down.

5. Adjust the drive chain slack. (See

page 7-25.)

6. Tighten the axle nut, and then

tighten the locknuts to the speci-
fied torques.

1. Drive chain slack adjusting bolt
2. Locknut

(a)

1. Wheel axle

1. Slot
2. Retainer

Tightening torques:

Axle nut:

150 Nm (15 m·kgf, 108 ft·lbf)

Locknut:

16 Nm (1.6 m·kgf, 12 ft·lbf)

U39P11E0.book Page 40 Monday, August 1, 2011 5:00 PM

Summary of Contents for FZ8NB













































































































Search results

Summary of Contents for FZ8NB

Reviews:

Related manuals for FZ8NB

Brands by name

Popular brands

Yamaha FZ8NB, Owner'S Manual

Search results

Summary of Contents for FZ8NB

Reviews:

Related manuals for FZ8NB

Brands by name

Popular brands