Yamaha FZ8NB Page 79 Owner'S Manual Download

Page: 79 / 108

PERIODIC MAINTENANCE AND ADJUSTMENT

7-35

7. Unhook the headlight bulb holder,

then remove the burnt-out bulb.

8. Place a new headlight bulb into po-

sition, then secure it with the bulb
holder.

9. Install the headlight bulb cover,

then connect the headlight cou-
pler.

10. Connect the coupler, then insert

the projection on the headlight unit
into the grommet on the vehicle to
fit the headlight unit in its original
position.

11. Install the headlight unit bolts.
12. Install the bolt behind the headlight

unit.

13. Place the side covers in their origi-

nal position, then install their bolt.

14. Place the top cover in its original

position, and then install its bolts.

15. Have a Yamaha dealer adjust the

headlight beam if necessary.

1. Headlight coupler
2. Headlight bulb cover

1. Headlight bulb holder
2. Headlight bulb

1. Projection
2. Grommet

U39P11E0.book Page 35 Monday, August 1, 2011 5:00 PM

Summary of Contents for FZ8NB













































































































Search results

Summary of Contents for FZ8NB

Reviews:

Related manuals for FZ8NB

Brands by name

Popular brands

Yamaha FZ8NB, Owner'S Manual

Search results

Summary of Contents for FZ8NB

Reviews:

Related manuals for FZ8NB

Brands by name

Popular brands