Yamaha FZ6-NV Page 82 Owner'S Manual Download

Page: 82 / 90

SPECIFICATIONS

8-1

Dimensions:

Overall length:

2095 mm (82.5 in)

Overall width:

755 mm (29.7 in)

Overall height:

1085 mm (42.7 in)

Seat height:

795 mm (31.3 in)

Wheelbase:

1440 mm (56.7 in)

Ground clearance:

145 mm (5.71 in)

Minimum turning radius:

2800 mm (110.2 in)

Weight:

With oil and fuel:

201.0 kg (443 lb)

Engine:

Engine type:

Liquid cooled 4-stroke, DOHC

Cylinder arrangement:

Forward-inclined parallel 4-cylinder

Displacement:

600.0 cm³ (36.61 cu.in)

Bore

stroke:

65.5

44.5 mm (2.58

1.75 in)

Compression ratio:

12.20 :1

Starting system:

Electric starter

Lubrication system:

Wet sump

Engine oil:

Type:

SAE10W30 or SAE10W40 or SAE15W40
or SAE20W40 or SAE20W50

Recommended engine oil grade:

API service SE, SF, SG type or higher

Engine oil quantity:

Without oil filter cartridge replacement:

2.50 L (2.64 US qt) (2.20 Imp.qt)

With oil filter cartridge replacement:

2.80 L (2.96 US qt) (2.46 Imp.qt)

Cooling system:

Coolant reservoir capacity (up to the
maximum level mark):

0.27 L (0.29 US qt) (0.24 Imp.qt)

Radiator capacity (including all routes):

2.00 L (2.11 US qt) (1.76 Imp.qt)

Air filter:

Air filter element:

Oil-coated paper element

Fuel:

Recommended fuel:

Unleaded gasoline only

Fuel tank capacity:

19.4 L (5.13 US gal) (4.27 Imp.gal)

Fuel reserve amount:

3.6 L (0.95 US gal) (0.79 Imp.gal)

Fuel injection:

Manufacturer:

MIKUNI

Model/quantity:

36EIDW x 2

Spark plug (s):

Manufacturer/model:

NGK/CR9EK

Spark plug gap:

0.6–0.7 mm (0.024–0.028 in)

Clutch:

Clutch type:

Wet, multiple-disc

Transmission:

Primary reduction system:

Spur gear

Primary reduction ratio:

86/44 (1.955)

Secondary reduction system:

Chain drive

Secondary reduction ratio:

46/16 (2.875)

Transmission type:

Constant mesh 6-speed

Operation:

Left foot operation

-20 -10 0 10 20 30 40 50 ˚C

SAE 10W-30

SAE 15W-40

SAE 20W-40

SAE 20W-50

SAE 10W-40

U1B322E0.book Page 1 Monday, August 8, 2005 1:49 PM

ProCarManuals.com

Summary of Contents for FZ6-NV



























































































Search results

Summary of Contents for FZ6-NV

Reviews:

Related manuals for FZ6-NV

Brands by name

Popular brands

Yamaha FZ6-NV, Owner'S Manual

Search results

Summary of Contents for FZ6-NV

Reviews:

Related manuals for FZ6-NV

Brands by name

Popular brands