Yamaha FZ6-NV Page 52 Owner'S Manual Download | Manualshive

Page: 52 / 90

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-12

WARNING

EWA12471

Be sure to place the hoses in their
original position as shown.

8. Install the seat.

EAU34300

Adjusting the engine idling
speed

The engine idling speed must be
checked and, if necessary, adjusted as
follows at the intervals specified in the
periodic maintenance and lubrication
chart.
The engine should be warm before
making this adjustment.

NOTE:

The engine is warm when it quickly re-
sponds to the throttle.

Check the engine idling speed and, if
necessary, adjust it to specification by
turning the idle adjusting screw. To in-
crease the engine idling speed, turn the
screw in direction (a). To decrease the
engine idling speed, turn the screw in
direction (b).

NOTE:

If the specified idling speed cannot be
obtained as described above, have a
Yamaha dealer make the adjustment.

1. Hose

1. Original position (paint mark)

1. Idle adjusting screw

Engine idling speed:

1250–1350 r/min

U1B322E0.book Page 12 Monday, August 8, 2005 1:49 PM

ProCarManuals.com

«
...
50
51
52
53
54
...
»

Summary of Contents for FZ6-NV



























































































Reviews:

No comments

Related manuals for FZ6-NV

Brand: KYMCO Pages: 58

Brand: HYOSUNG Pages: 98

Brand: R&G Pages: 13

COMFORT 10130810

Brand: Contracor Pages: 36

2006 G 650 Xmoto

Brand: BMW Pages: 132

Brand: KTM Pages: 36

Brand: R&G Pages: 13

Montana 7 Series

Brand: Garmin Pages: 24

Brand: Dynafit Pages: 20

Brand: hepco & becker Pages: 2

Brand: URAL Motorcycles Pages: 104

Brand: CyClone Pages: 24

Brand: VESPA Pages: 135

Marathon 125 AC EURO 4

Brand: RIEJU Pages: 45

Brand: Petzl Pages: 3

Brand: Petzl Pages: 8

Brand: Petzl Pages: 17

Brand: Petzl Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands