Yamaha FZ6-NV Owner'S Manual Download | Manualshive

Page: 65 / 90

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-25

6

EAU23290

Checking the wheel bearings

The front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrica-
tion chart. If there is play in the wheel
hub or if the wheel does not turn
smoothly, have a Yamaha dealer check
the wheel bearings.

EAU34371

Battery

The battery is located under the fuel
tank. (See page 6-11.)
This model is equipped with a sealed-
type (MF) battery, which does not re-
quire any maintenance. There is no
need to check the electrolyte or to add
distilled water.

To charge the battery

Have a Yamaha dealer charge the bat-
tery as soon as possible if it seems to
have discharged. Keep in mind that the
battery tends to discharge more quickly
if the vehicle is equipped with optional
electrical accessories.

1. Positive battery terminal

2. Negative battery terminal

U1B322E0.book Page 25 Monday, August 8, 2005 1:49 PM

ProCarManuals.com

«
...
63
64
65
66
67
...
»

Summary of Contents for FZ6-NV



























































































Reviews:

No comments

Related manuals for FZ6-NV

Brand: Kabuto Pages: 40

Brand: Ohlins Pages: 4

Brand: RPS Pages: 28

Brand: Cycle Protect Pages: 15

MCL-4000 Series

Brand: Dakota Digital Pages: 3

Brand: Ice Bear Pages: 64

Brand: Shark Pages: 80

Brand: Kemppi Pages: 10

Brand: Derbi Pages: 179

Brand: Shad Pages: 2

Brand: APRILIA Pages: 80

Brand: HYOSUNG Pages: 100

Brand: HYOSUNG Pages: 96

Brand: hepco & becker Pages: 2

Brand: APRILIA Pages: 386

Brand: KTM Pages: 118

Brand: Rivco Pages: 5

All New Classic 350

Brand: Royal Enfield Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands